ASA (Acrylonitrile-Styrene-Acrylate) Filament The 3D4MAKERS ASA Filament will be delivered in a vacuum packaging in our recyclable box. Technical information: Acrylonitrile-Styrene-Acrylate (ASA) polymers are amorphous and have mechanical properties similar to those of ABS plastics. However, the ASA properties are far less affected by outdoor weathering. The outstanding weather resistance abilities of ASA is due to the acrylic ester elastomer. ASA parts have good chemical and heat resistance, and high impact strength, even at low temperatures. Typical ASA applications are buiding/construction, automotive and recreation parts. Measurements & Tolerance Size Diameter tolerance roundness 1,75 mm Filament +/- 0,05mm 95% 2,85 mm Filament +/- 0,10mm 95% Physical properties Description Value Test method Density 1,07 g/cm3 ASTM D792 Melt Mass-Flow Rate (MFR) (220ᵒC/10KG) 12 g/10 min ASTM D1238 Mechanical properties Description Value Test method Tensile Stress 47 Mpa ASTM D638 Flexural Modulus 2210 Mpa ASTM
ASA (Acrylonitrile-Styrene-Acrylate) Filament
The 3D4MAKERS ASA Filament will be delivered in a vacuum packaging in our recyclable box.
Technical information:
Acrylonitrile-Styrene-Acrylate (ASA) polymers are amorphous and have mechanical properties similar to those of ABS plastics. However, the ASA properties are far less affected by outdoor weathering. The outstanding weather resistance abilities of ASA is due to the acrylic ester elastomer. ASA parts have good chemical and heat resistance, and high impact strength, even at low temperatures. Typical ASA applications are buiding/construction, automotive and recreation parts.
Measurements & Tolerance
Size
Diameter tolerance
roundness
1,75 mm Filament
+/- 0,05mm
95%
2,85 mm Filament
+/- 0,10mm
95%
Physical properties
Description
Value
Test method
Density
1,07 g/cm3
ASTM D792
Melt Mass-Flow Rate (MFR) (220ᵒC/10KG)
12 g/10 min
ASTM D1238
Mechanical properties
Description
Value
Test method
Tensile Stress
47 Mpa
ASTM D638
Flexural Modulus
2210 Mpa
ASTM D790
Impact strength Notched Izod
180 j/m
ASTM D256
Rockwell Hardness (R-Scale)
103
ASTM D785
Printer settings
Description
Value
Printer nozzle temperature
240 - 280°C
Heated bed temperature
90 - 110°C
Bed Adhesion
Magigoo Original on glass or a PEI Sheet
To get the best results while printing we advise you to keep the 3D printer in a room where there is hardly any draft and/or temperature fluctuations. Keep the 3D printer out of the sun. This cannot be a room where people sleep.
When the 3D printer is not being used it is important to keep the 3D4MAKERS ASA Filament in a bag and stored in a cool, dry and dark place until it is used again.
New 3D Print Materials Now Possible: 3D4Makers Develops Air-Cooled Filament Production System « Fabbaloo
Facilan™ Ortho Filament, 3D4Makers
Introducing the High Performance Recycled PEEK Filament
3DGence Consumables - Additive-X
3D4Makers.com
PEEK (Polyether Ether Ketone) Filament, The 3D4MAKERS PEEK Filament will be delivered in a vacuum packaging in our recyclable box. , Technical
PEEK Filament
3D4Makers Natural PLLA Filament 1.75 mm - 3D Compare Materials
, ABS KEVLAR has been designed for 3D printing by a precise formulation of aramid fibers into ABS materials. The aramid fibers assuring
ABS Kevlar Filament
R-PEEK filament, a high-performing recycled engineering thermoplastic that is excellently suited for high strength and high temperature 3D printing
R PEEK Filament